Power-Integrator I

• up to 204 Channels.
• 200MHz State Mode.
• 500MHz Timing Mode.
• Mixed State and Timing Mode.
• 4 Clock Inputs.
• Transient-Recording.
• 512K depth.
• 48Bit Time-Stamp unit (time correlation to other Trace).
• Free programmable trigger sequencer with 4 levels.
• 2 Trigger comparators with 64 Bit.
  8 Address selectors with 32Bit.
• 4 global event with no death time.
• Trigger Filter up to 2.5us.
• 3 Retriggerable 44 Bit Counters in the Trigger System.
• Trigger Output to Scope and Debugger Bus System.
• Binary, VHDL and Verilog storage system.

This Analyzer supports Protocol Analyzing (see Protocol Analysis Tab).
But for larger depth, especially for protocol Analysis, please see PowerIntergrator-II.

Power-Integrator-II

Over the time we can see, that some customer use the Logic-Analyzer for trace and analyzing Protocol Busses. In this case, a larger depth is very helpful. Power-Integrator-II serves exactly this. The different to the Integrator-I is, that we have reduce the number of Channels from 204 to 102 and increase the Memory from 512K-Frames up to 256Million-Frames.

• up to 102 Channels.
• 200MHz State Mode.
• 500MHz Timing Mode.
• Mixed State and Timing Mode.
• 4 Clock Inputs.
• Transient Recording.
• scalable memory up to 4 GByte depth.
• 48Bit Time-Stamp unit (time correlation to other Trace).
• Free programmable trigger sequencer with 4 levels.
• 2 Trigger comparators with 64 Bit.
  8 Address selectors with 32Bit.
• 4 global event with no death time.
• Trigger Filter up to 2.5us.
• 3 Retriggerable 44 Bit Counters in the Trigger System.
• Trigger Output to Scope and Debugger Bus System.
• Binary, VHDL and Verilog storage system.

Up to two Analog-Probes can connect to this Instrument.
This Logicanalyzer is preferred for use as Protocol-Analyzer. Up to 256Million-Trace-Frames.

Protocol Analysis

The Software can analyze Data Lane and display the Protocol-Level of the Serial Stream.

Direct supported are:

• CAN
• FlexRay
• LIN
• SPI
• USB
• I2C
• ASYNCH
• JTAG
• PCI
• DRAM

All protocols are delivered with source code and can be extended. A Interface is available for create user specific protocols.

MICTOR 38 Probe

Single ended Data and Clock

Active Probe with Mictor 38 Connector.

• 34 Channels Single ended
  32 Data Channels
  2 Clock
• Selectable threshold level for groups of 16 lines
• 0.1 .... 5.0 Volt
• 50KOhm
• 4pF

MICTOR 38 Probe

Single ended Data

Differential Clock Signal

Active Probe with Mictor 38 Connector.

• 33 Channels
  32 Data Channels single ended
  1 Clock Pair Differential
• Selectable threshold level for groups of 16 lines
• 0.1 .... 5.0 Volt
• 50KOhm
• 4pF

MICTOR 38 Probe

Differential Data and Clock

Active Probe with Mictor 38 Connector.

• 17 Channels
  16 Data Pair Differential
  1 Clock Pair Differential
• Selectable threshold level for groups of 16 lines
• 0.1 .... 5.0 Volt
• 50KOhm
• 4pF

SAMTEC-100 Probe
Single ended Data and Clock

Active Probe with Samtec 100 Connector

• 34 Channels
  32 Data Channels
  2 Clock Channel
• Selectable threshold level for goups of 16 lines
• 0.1 .... 5.0 Volt
• 50KOhm
• 4pF

SAMTEC-100 Probe
Single ended Data
Differental Clock Signal

Active Probe with Samtec 100 Connector

• 33 Channels
  32 Data Channels single ended
  1 Clock Pair Differental
• Selectable threshold level for groups of 16 lines
• 0.1 .... 5.0 Volt
• 50KOhm
• 4pF

STANDARD 100mil Probe
Single ended Data and Clock

Active Probe with 100mil Standard Connector

• 17 Channels
  16 Data Channels single ended
  1 Clock single ended
• Selectable threshold level
• 0.1 .... 5.0 Volt
• 50 KOhm
• 4pF

Analog Probe

12 Bit Analog Probe for recording Analog Signals.
This Probe has 4 Input Channels 0.0 ... 5V and additional 3 current Channels for external shunt resistors. In the combination, the Probe can Trace U*I in tree Supply Lines. For the Power measurement, the Analog-Trace is correlated with the Code Trace.

• 12 Bit resolution in each channels
• 4 Volt Channels 0.0 ... 5.0 Volt
• 3 current channels
• 625kHz sample / sec.
• Filter and Trigger capability on PT1 or PT2

DRAM/SDRAM Adaptation

Differen Adapters are available for DRAM, DDRAM2, SDRAM etc.

• 184 Pin DIMM
• 144 Pin SO-SDRAM
• 200 Pin SO_DDR
• 200 Pin SO_DDR2

Board Adaptation

Board direct adapters for Tektronix and Aglient Adaptions.